|
Table of Contents
About the ManualCanadian Department of CommunicationsDeclaration of ConformityTable of ContentsChapter 1 Introducing the MotherboardIntroductionFeatureOnboard LanBIOS FirmwareSpecificationMotherboard ComponentsChapter 2 Installing the MotherboardSafety PrecautionsInstalling the Motherboard Safety PrecautionsChoosing a Computer CaseInstalling the Motherboard in a CaseChecking Jumper SettingsSetting JumpersChecking Jumper SettingsJumper SettingsInstalling HardwareInstalling the ProcessorCpu Installation ProcedureInstalling Memory ModulesExpansion SlotsConnecting Optional DevicesInstalling a Hard Disk Drive/CD-ROM/SATA Hard DriveConnecting I/O DevicesConnecting Case ComponentsAtx 12V Power ConnectorFront Panel HeaderHard Drive Activity LEDPower/Sleep/Message Waiting LEDChapter 3 Using BIOSAbout the Setup UtilityEntering the Setup UtilityThe Standard ConfigurationUsing BIOS about the Setup UtilityResetting the Default CMOS ValuesUsing BIOSStandard CMOS SetupAdvanced SetupAdvanced Chipset SetupIntegrated PeripheralsPower Management SetupPci/Pnp SetupPC Health StatusFrequency/Voltage ControlLoad Default SettingsSupervisor PasswordUser PasswordSave & Exit SetupExit Without SavingUpdating the BIOSChapter 4 Using the Motherboard SoftwareAbout the Software DVD-ROM/CD-ROMAuto-Installing under Windows Xp/Vista/7Running SetupManual InstallationUtility Software ReferenceChapter 5 Setting up Ejiffy IntroductionInstallation and BIOS SetupEntering EjiffyFeatures IconsUsage FAQChapter 6 Trouble ShootingStart up Problems During AssemblyStart up Problems after Prolong UseMaintenance and Care TipsBasic Troubleshooting Flowchart
Advertisement
Quick Links
x
Download this manual
10
Motherboard Components
11
Installing the Motherboard
12
Checking Jumper Settings
28
Front Panel Header
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits govern-
ing this device. Changes or modifications not expressly approved by the system ' s
manufacturer could void the user's authority to operate the equipment.
Preface
Preface
Table of Contents
Previous Page
Next Page
1
2
3
4
5
Advertisement
|